And the iPhone is a rather elegant thing, and perhaps the moment has come when the device simply does not have any effect on keystrokes and is not activated. There may be a million explanations for this, but everything has its own reasons, everything can be explained in some way. Maybe you accidentally sat on top of it while the phone was in the back pocket of your pants, or it was raining heavily and it got wet. Of course, if the smartphone drowned in a bathtub, where water was poured to the top, or fell on solid ground from the balcony, it will hardly be possible to solve the problem on its own, and in any case, you will have to visit the service center. But if such critical actions were not performed with the device, there is a 90 percent chance that we will have a chance to return the gadget to work on our own. The main thing we need to do is take into account the signs given by the apparatus, and use them with benefit and arrangement to correct the situation in our favor.
IPhone 6 does not turn on - completely black screen and nothing changes
The most common case of an iPhone inoperative. The screen does not want to light up in any way, and regardless of your actions, there is no reaction to them. The most likely explanation for this fact is a completely dead battery or a dead axle. First, we will discuss the first option, we will discuss the second explanation of this behavior of the gadget a little later. What measures should be taken if it does not turn on, or another modification?
1. Maybe you live in a cold area and the winter is very harsh in your area. In this case, a very likely explanation for the inoperative state of the phone is too cold temperature. Do not be surprised, because of the cold weather, Apple devices often stop responding to taps and turn out to be faulty for a while. Place the gadget in a warm temperature and proceed to step # 2.
2. Connect the charger to the device and wait at least 15 minutes. If we determined the diagnosis correctly and were not mistaken with the reason, the device activates itself after a short time. Otherwise, proceed to the next step.
3. Hold down the Home and Power keys at the same time. Do not release the keys for 15-20 seconds, namely until a glowing apple appears on the display of the device. Then the keys can be released. Finally, wait approximately 1 minute until iOS is fully launched.
4. It happens that before referring to step # 2, it is necessary to activate / deactivate the silent-mode switch several times at regular intervals. In part, if the simultaneous pressing of two keys (HOME and POWER) did not bring the expected result, such a measure of the way to bring the desired effect.
In the case when none of the above measures has had the desired result, and the iPhone 6 still does not turn on, the explanation may be as follows: one of the components of the smart simply failed. The cable for charging the device could also break, or the charging itself turned out to be faulty. It is worth trying to charge your phone with a different charger.
The program running on the iPhone freezes during operation
It may happen that the application on the iPhone 6 stops launching and freezes. In these conditions, it is necessary to close it forcibly and unload the application from the phone's memory. To forcibly close the application, we carry out the following sequence of actions: double-click the Home button, and then swipe up to minimize the problematic task.
IPhone 6 does not turn on - smart does not respond to tap buttons
From time to time, the following happens: the gadget stops activating and responding to any button presses. In addition, the screen in a suspended state displays a screenshot of the last program that you launched, but it does not work to close it. If you find yourself in just such circumstances, perform a hard reset of the smart. To bring it into effect, keep the Home and Power keys pressed for 10 seconds, and you will get the effect you want from the reboot.
IPhone 6 does not turn on - the display shows an apple all the time
It may happen that the smart does not react to the user's actions, an apple appears and disappears on the screen again, and this behavior takes place to be constant. Usually, the explanation for this behavior of the phone is an incorrect iOS update, a crooked hack, or a small glitch in the process of restoring a backup copy (in other words, a backup) of the device. If it may seem to you that the days of the device are already numbered, you should not rush to draw such global conclusions. In response, let's try to bring it back to life, in particular by running recovery-mode. So, if your iPhone won't turn on, what should you do?
1. Launch the iTunes program on your computer and plug the USB-cable into a free port on the PC (there is no need to connect the cord to the smartphone itself)
2. Turn off the power of the device while holding down the Home + Power buttons
3. Keeping the Home button pressed, connect the USB cable to the device
4. Hold down the Home key until the iTunes logo and an image with a plug appear on the device screen
5. A message will appear on the PC display notifying you that the device is in recovery-mode
6. Then tap the "Restore" button. Then it is worth waiting for a certain period: until the device is restored to default settings, the latest version of iOS will be downloaded to the computer. During the boot process, the smart will simply lie with a dark screen and not respond to button presses. Even if your network connection is stable and fast enough, the download may take up to 30 minutes or longer. If your Internet connection is not very fast, the process may not end at all. So you should first take care of the reliability of the Wi-Fi connection.
Now you know what to do if iPhone 6 or earlier does not turn on. We hope that this article will become a guide for you to restore the device to work if it looks faulty, and it will take you very little time, and it will not cost you any financial costs.
In the article, we will look at the main reasons why the iPhone turns off by itself, what led to this and how to solve the problem now. The material is relevant for all models of iPhone X / 8/7/6/5/4 and their modifications S and Plus.
iPhone is the accessory that provides endless communication possibilities, while being a stylish gadget that emphasizes the excellent taste of the user. Every day, people spend a lot of time texting with each other, calling, surfing the Internet.
The smartphone has taken a big place in human life. It is all the more offensive when the device malfunctions during operation. Serious Malfunction - iPhone shuts down by itself. During an important conversation or correspondence, the device may simply go out, causing a lot of negative emotions. There are several reasons and ways to fix the trouble. Let's consider each separately.
Battery problems
This is the most popular, common reason. The malfunction can occur in several cases.
- The phone fell, causing the battery contacts to disconnect. But this phenomenon is not permanent. The fact is that the contacts did not break off, but simply disconnected and now spontaneously change position. The smartphone may work fine, but as soon as the owner shakes it (by pulling it out of his pocket or in some other way), the contacts of the iPhone battery will disconnect from the power board, which will turn off the device. The charge level does not matter.
- Non-original battery. This happens when cheaper Chinese counterparts are installed when replacing the "native" battery. The capacity of these batteries may be insufficient a priori. But the phone will still work. Only during operations that require a lot of energy (Internet surfing through the switched on Wi-Fi and simultaneous conversation on the cellular line), a power surge will occur, and the battery capacity will drop to zero - the phone will turn off.
- The battery is defective. Each battery has its own specific recharge limit, after which it begins to deteriorate. Another situation is when the iPhone is exposed to temperature extremes - for a long time arriving in a too warm or cold environment.
How to fix
If the loop contacts break, you should contact the service center - it's good if the iPhone warranty is still valid. An independent unskilled solution to the problem is fraught with more disastrous consequences.
When a non-original battery is used, the way out of the situation is simple - change to a certified one. Just first you need to find out the power that the phone consumes, and then purchase the appropriate battery.
When the battery is faulty or has worked out, then we proceed in the same way as in the previous method - we buy a suitable original battery. There is one important point here. Replacing the iPhone battery is not an easy process. You can find tons of instructions on this topic on the Internet. But in reality, sometimes everything is different. In addition to skills (or at least experience), the user will need a special tool. Its cost varies. It will be easier to immediately refer the iPhone to specialists who will quickly change the battery for a modest fee.
Power controller problems
Apple smartphones are devices where everything is thought out. There is a special chip that controls the voltage supplied during charging. The phone's battery is powered from the AC mains through a special adapter. Before getting into the battery, the voltage passes through the power controller (the same chip). It acts as a barrier that prevents damage to the battery. When the voltage meets the requirements of the battery, then charging is in progress, and when it is higher, the chip is triggered, preventing the pulse from reaching the battery.
If iPhone turns off by itself, it may mean a breakdown of the power controller. In this case, the phone's operating system tries to “protect” the battery from power surges.
Repair method
Only the specialists of the service center can correct the situation. Replacement of the failed power controller will be required. This process is associated with work in the iPhone motherboard, where unprofessional actions will lead to the complete unusability of the device.
Operating system errors
iPhone, like any modern device, has many functions. One of them is direct interaction with the components of the phone. This is done by reading information from certain sensors. But this function does not always play into the hands of the owner. Certain software bugs cause the iPhone to turn off by itself when fully charged.
How to fix the situation
The first and easiest option is to completely reboot the device. To do this, you need to simultaneously hold down the power and Home buttons. They should be held in this position for at least 15 seconds. If the restart is successful, the manufacturer's logo will appear on the display.
It happens that the charging indicator is faulty. It has already been noted that the system works with iron in complete symbiosis. There is an error in which, despite the fact that the battery is charged, the corresponding indicator shows "0". The system immediately reacts to this by turning off the phone. The fix is \u200b\u200beasy:
- We completely discharge the iPhone.
- We leave it in this state for 2-3 hours.
- Then we connect the charger.
- We charge up to 100%.
Another way to deal with errors is to restore the operating system. The process is carried out through the iTunes program (any user of Apple devices has it). Then we get a completely "clean" gadget with the newest (available) operating system. Before restoring, in order to avoid the loss of important information, you should make a backup copy of the data in the same iTunes or save it on the iCloud cloud server.
Conflicting Applications
There are applications that, when activated, conflict with the operating system. This is caused by the incompatibility of the program and the IOS version, the result of which is the shutdown of the device. There are two ways out of the situation.
- Upgrade your operating system if available.
- Remove conflicting application.
Some programs require additional hard disk space. An example would be a photo editor that processes an image by saving the result separately without touching the original. When there is not enough memory, the system can react by turning off the phone. Exit: free up space on your hard drive or not use the application.
iPhone may shutdown due to CPU overload caused by a large number of concurrent applications. The component is overheating and to protect it, the operating system gives a shutdown command.
Water ingress
Water, along with dust, is the main enemy of digital technology. If moisture gets inside the gadget, the device stops working correctly. This may manifest itself in the fact that iPhone turns off by itself and turns on only with charging... In order not to ruin the device completely, you should contact the service center, where the phone's iron will be dried. It is not recommended to get rid of moisture inside the smartphone on your own.
4.2 (83.33%) 6 votes.
Sometimes even iPhones with good batteries start to fail. In some cases, there may be problems with the chemistry of the battery. It happens that the owners of telephones leave them on heating devices (on a torpedo under the sun) or the like, thus “burning” them. Often a buggy battery can be fixed by following the tips below. So, if your iPhone shuts down unexpectedly and the battery still shows 20%, 30%, or even 50%, here's what to try!
Note... Apple has a program for iPhone 6s owners who are experiencing an "unexpected shutdown problem." This applies to the iPhone 6s, which was released between September and October 2015. If you think this applies to you, check the serial number at apple.com to see if you can replace the battery for free.
1. Update to iOS 10.2.1 or newer
In earlier versions of iOS, if a power-hungry app such as suddenly increased power demand, and your battery was already weak due to excessive charge cycles or exposure to heat, your iPhone could accidentally shut down before the battery dropped to zero. to protect yourself. Apple updated its battery management in iOS 10.2.1, fixing the issue 80% of the time.
So, if you are still on the old firmware, update your device to iOS 10.2.1 or newer. The latest version is always better as it fixes bugs and security vulnerabilities.
2. Hard reboot
Whether the iPhone has actually started shutting down earlier, or if one of the processes is quickly draining the battery, a forced restart can help. Remember when your computer is buggy you do a "Windows restart", this is no joke, sometimes the bad bits get stuck and need to be "flushed".
- On iPhone 6s and older phones, press and hold the " Power supply"And" Home».
- On iPhone 7 or later, press and hold the " Power supply"And" Decrease volume».
- Keep them in this position until you see the Apple logo.
- Let go.
After restarting your iPhone or iPad, wait and see. If it stays on and operational, everything is fine. If not, or if it doesn't reboot, proceed to the next step.
3. Connect
If your iPhone or iPad is running low on power quickly, after connecting to a charger, make sure it starts charging and can read the battery level. The absence of a charge indicator means that the battery is not charging. Partial or full charge - 20%, 30%, 50% or more - means you may have another problem.
Thus, plug your iPhone into the charging cable, plug it into a wall outlet or USB port, and start charging. Let it charge for an hour. If it doesn't seem to charge, try using a different charging cable, a different USB outlet, or a different USB port on your computer. Then, keep an eye on your iPhone or iPad and see if it turns off again. If not, great. If so, keep reading.
4. Recovery
After trying the simple tips, it's time to try the harder ones. In this case, restore your iPhone. iTunes is a safer way than iCloud as it actually offloads, reinstalls and reloads your data rather than doing everything locally and on your device. It can sometimes loosen up the bad bits that even a hard reset or restore from iCloud won't fix.
- Connect your iPhone, iPod touch, or iPad to iTunes on your Mac or Windows computer using a cable.
- Go to the " Device" in the upper left corner.
- Click " Backup».
- Wait for the backup to complete.
- Click " Reestablish».
- Wait for recovery to complete
When you're done, check if your iPhone or iPad is disconnecting. If so, hurray! If not, there is more to try.
5. Contact Apple
Sometimes the problem is really the problem. As with any electronic device, batteries can fail and cycles can be short. If you've tried all the methods and the iPhone keeps shutting down unexpectedly before the indicator reaches zero, go to a service center and replace the battery.
Also, you have a chance that Apple's diagnostics may be that the battery failed prematurely due to their fault, in this case, you can get a free replacement.
If you don't live near the Apple Store, you can call 1-800-MY-APPLE to set up mail repair. If you don't have AppleCare, you might have to pay for the call, but that's less of a waste than a dead iPhone or iPad.
Have you solved the problem?
If you have an iPhone that shuts down before the battery actually runs out and one of the above fixes worked for you, let me know! If the unwritten method above helped you, let me know, thanks!
Defective power chip
The power microcircuit breaks down from shock, moisture and voltage drops. It also breaks down through external factors and internal failures.
Power controller 2400 rubles. + installation 499 rubles. - from 1 hour
Power chip strapping
A strap is a large row (from 10 to 100+) elements on the board. She is responsible for the operation of the iPhone 6.
Diagnostics required - 0 rubles. - from 1 hour. At the end of it, let's call the cost of the repair.
It can also be:
Processor, power supply microcircuit, network processor and strapping of these microcircuits. They are associated with the entire apparatus. Their breakage causes extensive damage.
After that we will inform you the cost.
Moisture or strong shock
Any malfunction may occur, as moisture and mechanical damage affect the entire device.
Diagnostics required - 0 rubles. - from 20 minutes.
At the end of it, let's call the cost of the repair.
Video instructions for eliminating breakage
If iPhone 6 turns off, watch the video tutorial, which explains the cause of the problem and how to fix it.
You can watch the rest of the videos in the section quality control
After watching the video, you understand why the iPhone 6 turns off, how to restore it, and how to make a diagnosis. Having found out why the iPhone 6 turns off when you make a call or call, you can proceed to the repair itself. There are 2 ways in which you can repair the equipment:
1. Repair the device in the service - highly qualified employees of the center will eliminate the breakdown with high quality.
2. If the iPhone 6 is constantly disconnected when charging, individual repair of equipment is possible - accessories, tools can be purchased from us.
If you cannot continue operation due to outages, go to our service center, where an inexpensive, high-quality repair of any complexity will be done.
Fault description and remedies:
If the phone does not work as it should, it turns off during work or when making a call, this happens for several reasons:
1. Very often, a faulty battery becomes the reason why the iPhone turns off when you make a call or call. If the battery has lost its capacity or there is an increased consumption, then it will need to be replaced.
2. Excess consumption, as a rule, appears in the event of a strong shock or penetration of liquid into the apparatus. In this case, in order to determine the breakdown, it is important to make a diagnosis.
If suddenly you need a quality repair, then come to our service center. We use only original spare parts from Apple in our work, and therefore a 1-year warranty is issued. Contact Apple Service and you can continue normal operation.
How to troubleshoot: iPhone 6 turns off
If the iPhone 6 turns off, we recommend that you show the equipment to our specialists as soon as possible. To do this, come to our Gsmmoscow service center yourself or call a courier who will deliver your smartphone to the service for free. You can find the exact address in the contacts.
After you hand over the device to us, we will provide you with the following services:
1. First of all, we carry out full diagnostics. We will accurately determine the reason why the phone turns off in 20-30 minutes.
2. After determining the breakdown, we will inform the customers about the breakdown, as well as the timing and cost of repair. Under any circumstances, if it is necessary to replace the battery, our masters will take a little time for this.
3. After we succeed in eliminating the breakdown, customers are issued a 1-year warranty, because all the spare parts that we use in our work are original.
4. We have provided you with a complete price list. Call our operator if you need to consult on the cost or get other information.
Of course, if the iPhone 6 is constantly turned off when charging or during operation, you will not be able to continue operating further. It is necessary to solve this problem as soon as possible. Our Apple service center works on the most favorable terms. Here, experienced and qualified craftsmen will be able to quickly eliminate any breakdown. We employ professionals, they always know what to do and how to restore the normal performance of your smartphone as soon as possible.
Do you urgently need to fix a breakdown?
If the iPhone 6 is damaged at a very inopportune moment, and you do not know what to do, go to our service center. If you just need to change the battery, our specialists will do it within 20-30 minutes. We do urgent repairs in the Zhsmmoskov service at the request of our clients. You will not have to pay extra for the service.
You can also use such services of our service.
the iPhone turned off and does not turn on - a problem that every owner of Apple smartphones faces at least once in their life. Below we will consider all the most common reasons why a smartphone does not want to turn on. I will not touch on the reasons related to the hardware problems of the iPhone, since this is a job for service centers and it will be unrealistic for an unprepared user to fix it at home.
How to turn on iPhone
Before we proceed to directly find out the reasons why the iPhone does not turn on, we will check 2 points that are not directly related to any malfunctions.
- If the phone has turned off due to low battery power, it takes some time to turn it on. Keep the smartphone on charge for at least 15 minutes - this will be enough for the battery to gain the necessary charge. Try to enable. Doesn't turn on? Read on.
- If you are sure that the battery charge was sufficient, but nevertheless the iPhone does not turn on, the reason may be the firmware freezing or the smartphone switching to save mode. In this case, a hard reset of the smartphone will help us.
- For all models except iPhone 7 - simultaneously press and hold the power and Home buttons for about 20 seconds.
- For iPhone 7, you will need to simultaneously hold down the power and volume down buttons for the same 20 seconds.
In the best case, the phone will turn on and you can continue to use it as usual. If it doesn't help, read on.
Software malfunction
And while Apple devices are rightfully considered more reliable than smartphones from other manufacturers, they are also prone to crashes, freezes and other software bugs. The causes of such malfunctions are usually:
- A large number of simultaneously running applications.
- Jailbreak firmware
- Errors during device update
- Magnetic storms, gypsy curse and other unknown reasons ...
The cardinal way to solve iPhone software problems is to flash through itunes in DFU mode. In this case, we need a computer and a USB cable (it is better to use the original one).
It should be understood that during the flashing, all data from your phone will be deleted, so it is recommended to periodically create backups and this applies not only to iPhones.
- Download and install the iTunes app
- Run the installed application and connect iPhone to computer
- Press the Home and Power buttons at the same time, count to 10 and release the power button. Hold the Home button until iTunes says iPhone is connected in recovery mode
- In the window that appears, you must click the "Restore iPhone" button and confirm again in a new window.
- iTunes will download and install the latest firmware for your device.
Recovery in DFU mode is the maximum that an untrained user can do on his own. If this method did not help, then most likely the malfunction of the smartphone is related to hardware problems.
Hardware malfunction
If none of the methods described above helped you, we can most likely say that the problem is in the hardware of the smartphone. There may be several reasons:
- Normal wear and tear of electronic components
- Water or other conductive liquids entering the device
- Battery failure
- Malfunction resulting from the use of non-original accessories - charger, cable
- Damage to smartphone connectors
Do not try to disassemble the iPhone yourself, even if you suspect a specific malfunction. Unskilled intervention can end in disaster for your iPhone, entrust this work to professionals.
iPhone has turned off and won't turn on - contact the service center, trying to repair yourself will only aggravate the situation and increase the cost of further repairs.
