The machine has stopped heating the water, but all the programs are set correctly? This means that you need to replace the heating element in the washing machine. We will describe in detail the process of dismantling and installing a new heating element, as well as share useful tips.
Operation of heating elements: it is clearly visible here how the service life affects the state of the heating element.
Heating element device and signs of its breakdown
Before replacing the heating element in the washing machine, it is recommended that you familiarize yourself with the principle of its operation. Heating element is a heater, the task of which is to heat the water in the tank. The main part of modern heating elements is a tube. A spiral passes inside it, which is separated from the outer walls of the tube by a dielectric material. The heater breaks down more often than other elements due to the fact that this spiral is constantly cooling and heating up. After losing its properties, it fails. This is often due to the formation of deposits on the heater tubes. Therefore, the main sign of breakage is a thick layer of plaque.
To prolong the life of the heating element, it is recommended to clean it every 3-4 months.
To understand that it is necessary to replace the heating element of the washing machine, you can also on another basis - the water in the barrel stops heating. Sometimes the reason for the lack of hot water is an incorrectly set washing program. If all the settings are set correctly, then you can immediately proceed to replacing the heating element.
Also, the reason for the lack of hot water can be an inoperative programmer or water heating sensor. It is better to entrust the replacement of these elements to professional repairmen. In any case, after dismantling the heater, you will understand whether it is the reason for the lack of hot water in the machine or not.
What do you need to replace?
However, before you start work on the replacement, you should arm yourself with the following parts and tools:
- New heating element. You can buy it at the manufacturer's service center (or get it free of charge under warranty). We do not recommend buying a used part, as after a while you will have to replace it again;
- A set of screwdrivers (usually a slotted screwdriver is enough);
- A set of wrenches and tubular wrenches;
- Rubber hammer;
- Adhesive sealant (if a used heating element is used for replacement).
Step 1 - find the heating element in your model
To get to the heating element, you need to carry out a partial analysis. Each washing machine has differences in its design: in some models, the heating element is located on the front of the case, while in others, on the back. In order not to waste time on lengthy dismantling of both covers, you need to decide which one is behind the heater:
- If the back wall is large and removable, the heating element is most likely installed behind it.
- If the back wall does not look voluminous, and at the same time you do not see obvious fastenings, then the heating element is located at the bottom of the front wall.
We dismantled the cover, now we need to find the heating element. It is located inside the tank, only the terminals with wires can be seen from the outside. The following photo will help you find the heating element:
Disconnect the wiring and check if the heater is working or not. This can be done using a conventional tester. Fears were confirmed, and it does not work? Then we proceed to the replacement.
Step 2 - remove the non-working part
You have prepared a new replacement part. Dismantling can now begin.
IMPORTANT: there must be no water in the tank. To drain it, you must unscrew the drain filter.
Now we take the tubular type wrench and remove the central nut - it is marked with the number "1" in the photo.
After removing the nut, it is necessary to sink into the studs (2). A key handle, a screwdriver or a rubber hammer will help here - push the pin so that it goes inside the heater.
The fasteners are removed, so it remains to remove the heating element, which is tightly seated on a rubber gasket . In order to loosen the seal, it is necessary to pry the heating element with a slotted screwdriver. The photo above shows where you need to start getting the part. Remember in which position the heating element was installed. Remove the heater carefully, using a slotted screwdriver from different sides.
Useful advice! There are a lot of wires that connect the heating element to the washing machine, so you can easily forget their original location. Before dismantling, take a photo of the assembly with your phone or camera to ensure that the wires are connected in the correct order.
Step 3 - installing the new item
The main part of the work is done - we removed the non-working part. Now we take a new heater and install it in the bore. Here, too, the help of a screwdriver can come in handy, since the element comes in tightly due to the rubber seal. Make sure the part is level - there should be no displacements or distortions. The replacement of the heating element of the washing machine is almost complete - it remains to install the mounts. To do this, we screw the mount onto the hairpin. .
It is necessary to tighten the hairpin carefully: if you push it, then the heating element can fall into the drum. We remember how the wires were attached and put them in their place. It remains to assemble the back wall, and this replacement can be completed.
Important! Some masters who specialize in the repair of washing machines advise placing the heating element on a sealant to prevent water leakage. If you purchased a new part and installed it correctly, the heating element will “sit” tightly even without the use of glue.
It is recommended to immediately check the operation of the new heating element. To do this, you need to start the wash, setting at least 50 degrees. Wait 15-20 minutes and then touch the hatch. If its glass is warm, then the washing machine is working properly.
Video: how to change the heating element?
In the next video, the home craftsman will clearly show how to replace the heating element in the washing machine, regardless of its model and manufacturer:
Now you know how to replace the heating element in a washing machine. It is recommended that you undertake a do-it-yourself replacement if you have experience in repairing household appliances. Perform all actions from the instructions carefully, since wires and terminals are fragile elements. Do not forget to check the heating element every 3-4 months. To consolidate the information received, we recommend watching a video showing the replacement of the heating element of the washing machine.
In contact with
First you need to figure out what constitutes a heating element for a washing machine. This is a special heating element that brings water to the temperature set by the program. Based on the type of model and manufacturer, heating elements can be located in different places of the machine: in front or behind. However, as a rule, it is located at the bottom and 2 wires must go to it.
If the washing machine stops heating the water, the first step is to check the heating element.
Despite the fact that the heating element can serve faithfully for 10 or even more years, it still breaks down more often than all other elements due to constant contact with hard water. Scale begins to deposit on it, which over time becomes the cause of its malfunction. You can descale the heating element at home. But it is better to use special protective equipment to prevent its formation, for example, Calgon.
In order to make a replacement, no special skills are required and in most cases it will not be difficult. For example, you can take a Samsung typewriter, which has a heating element in the back.
Before proceeding with the replacement of the electric heater, it is necessary to disconnect the machine from the mains.
In order to get into the washing machine through the back panel, the latter must be unscrewed and removed. With those models where the lid is located on the front, you will have to tinker a little. In order to unscrew it, you will first need to remove the clamp that holds the cuff. Based on his model, you will need to arm yourself with a screwdriver or pliers. To prevent the cuff from interfering in the future, you can wrap it inside the tank.
Now it remains to remove the top panel and the control board with the door lock. Moreover, it is not at all necessary to pull them out, you can simply unscrew all the bolts and put them so that they do not interfere. Next, the dispenser tray is removed, after which it is necessary to go to the bottom panel. After all this is removed, a front wall will appear in front of us, after disassembling which you can get to the heating element.
All wires are preliminarily removed from it, and the fixing nut is unscrewed, which must be pressed inward and the heating element removed. There will be a lot of scale on the heater, so you just need to replace it with a new one and put all the parts in their places.
Owners of washing machines Indesit will help to change the heating element by a detailed step-by-step algorithm with a photo, which is given.
Where to buy a heater
The tubular element itself is not irreplaceable and can be purchased in a large number of places. The first step is to contact the service center of your washing machine, where a specialist will select a suitable option and even offer services for its replacement.
How long will the new heating element last? It depends solely on the means that are used (or not used at all) to soften hard water.
In addition to contacting a service center, you can buy an electric heater in any market where spare parts for washing machines are sold. The main thing is to choose the most suitable option as accurately as possible. Before buying, you need to take it out of the box and check its compliance by comparing it with the old one.
It is best to buy a new heating element rather than a used one, since its cost is not so high. After installing the used heater, the machine will wash, but soon you will need to buy this item again.
Before you start washing, you need to make sure that the heating element is installed correctly and is connected to the electrical network.
Now you know how to choose and install a new heating element on your washing machine in the event of a breakdown. As you can see from the instructions, there are no difficulties in this, and if you have a minimum set of tools and a few minutes of your time, you can easily do all the work yourself, without involving a specialist.
If the water in the washing machine does not heat up during washing, then in most cases it will be necessary to change the heating element. It is called a heating element, if it is defective, it needs to be replaced. Consider removing the heating element from the washing machine LG, Samsung, Candy, Bosch, Indesit and other popular brands.
The location of the heating element in washing machines, depending on the brand
Since the heating element is always in the water, it is located at the bottom of the drum. At the same time, it is necessary to get this element from different models in different ways. You can get to the heating element to replace it in the following ways:
- through the front wall;
- through the back wall;
- through the side wall.
In the photo you can see different options for the arrangement of elements.
In cars such as Samsung, Bosch or Veko, the heating element is located both behind and in front of the tank. To determine which cover of the washing machine to remove, you must start the inspection from the back wall.
When the cover at the back of the machine is full-sized, or occupies almost the entire rear wall, then it is most likely that the heating element is located at the back of the tank. And to get to it, you need to unscrew all the screws that are located along the perimeter of the back cover.
When the cover on the machine panel occupies a small part of it, it is usually necessary to access the belt. And you can change the heating element through the front panel, since it is attached in front of the tank. If in doubt, you can first remove the cover on the back of the machine to be sure.
You can remove the heating element from the Indesit, Ariston, Atlant, Candy and a number of other models washing machine only by removing the back panel. To get to the heating element, you need to unscrew all the screws used to secure the cover.
For some front-loaded cars, you can get to the heating element by removing the bottom panel on the front side. To remove it, you need to unscrew a couple of screws located on the side.
To change the heating element for models with a vertical type of loading, you need to remove the left or right side panel. It is usually secured with several screws to the rear panel and using one screw from the bottom of the front of the machine.
How to replace the heating element using the example of the Bosch brand
It should be noted that you can remove the heating element from the Samsung washing machine by following these instructions. Since many Samsung washing machines have the heating element located in the same way.
The order of work will be as follows:
- First of all, you need to de-energize the washing machine;
- To get to the heating element, you need to remove the bezel. The first step is to remove the top panel by unscrewing a few hex screws. To speed up the process, you can use an electric screwdriver;
- The next step is to remove the detergent dispenser. This can be done by pressing a special latch lock;
- Next, you need to remove the front wall. To do this, you will have to unscrew a few screws, this will allow you to remove the control panel, which can be removed upward without disconnecting the wires. Then you need to remove the bottom panel. Then you need to disconnect the cuff on the hatch, it is secured with a spring clip. They differ depending on the modification, however, for all models, it is necessary to pull on it. After that, the cuff moves inward, and all the screws holding the front wall and blocking the door are unscrewed;
- Ten is at the bottom of the tank. It is necessary to disconnect all wires with which the heating element is connected. To remember how they are connected, you can take a photo on your phone, this will help you connect them correctly during assembly;
- The nut of the heating element must be unscrewed. Do not twist it all the way, this will allow you to remove the heating element by pressing on the gasket;
- After removing the heating element, the next step is to remove the thermostat. It can be installed in a new heating element. You can apply a few drops of dish detergent to the seal, this will simplify the process of installing the part;
- The new heating element must be pressed firmly in order to properly fit into place. It is fastened by tightening the nut. If the seal is well fixed, you can start connecting the wires;
- The final step will be to install all parts in reverse order.
This manual is suitable for almost all models of Bosch (Bosch), Samsung (Samsung) and a number of other brands.
Replacing the heating element located at the rear of the drum
In many LG, Ariston, Indesit and Atlant washing machines, the heating element can be replaced through the back panel. Consider how you can remove the heating element from the Ariston washing machine.
In this case, the process of removing and installing a new heating element is much easier. There is no need to remove the front panel and control panel. To remove the rear cover, you need to unscrew a few bolts.
As in the above case, it is best to first photograph the location of the wires. After that, you need to disconnect the wires and loosen the nut. You do not need to completely untwist it to the end, it must remain on the thread. Next, the pin is pressed in to remove the heating element.
Before finally assembling the washing machine, check that all parts are sealed. To do this, you can pour water into the drum without starting the wash. If water leaks, tighten the nut. And only after that complete the assembly of all parts.
In this case, the new heating element must be a complete analogue of the old one. And to simplify the process of replacing a failed heating element, it is best to remove the drive belt.
For installation, it is best to purchase a new heating element, the used one will last much less, and then it will need to be replaced again.
To buy a heating element, you can contact the service department, where identical washing machines are serviced. You can buy heating elements in the online store.
The video below will allow you to clearly see how to replace the heating element in the washing machine.
How to remove it? - you ask. I'm telling you. It is necessary to release the center pin ( click on the picture - it is schematically shown there), which is located on the heating element itself, between the contacts. To do this, you will have to unscrew the two nuts located one on top of the other and securing the ground wire. It's a tricky design. The heating element is held by the compression of the gum of the seal. The elastic is compressed by this very hairpin and increases in breadth, closing all the cracks.
Unscrew both nuts, push the pin a little inward. Now we take the pliers and pull strongly on the contacts (electrodes) of the heating element. They are strong and we no longer feel sorry for them. We pull in turns and swing from side to side. We remove the heating element.
3. We clean the place of landing of the heating element
We remove the heating element and all the dirt from under the drum of the machine. Dirt is the cause of the problem. There will be a lot of dirt. It is important to pull out all of it so that it does not interfere with the work of the new heating element. In order to wash out all the dirt, you can first select everything with your long fingers, then take a bottle brush and continue with it. Then pour some water into the drum, after placing the basin in the place where the heater is removed. In a word, it is necessary to wash everything that has accumulated there over the years.
4. We buy a new serviceable heating element
The heater itself would also be useful to clean up. With it, you will go to the workshop to buy a replacement.
It was not difficult to find a suitable heating element. Take an old copy and stomp into the nearest washing machine repair shop. If possible, it is better to buy an original heating element, and not an analogue from China. In my case, the heating element cost 1,100 rubles.
Particular attention should be paid to:
- the length of the heating element. It must match the length of the old one;
- electrical power. It must match the markings on the old one;
- the width of the elastic. This is more important than it might seem at first glance! This is especially important in the case of the selection of an analogue. If the gum is 1 millimeter wider, then you will be trying to cram something that is not puffy. If at however, after you install it, during hot washing, the heating element can be "spit out" by the washing machine, no matter how hard you twist it.
Yes, little things, but our whole life consists of little things. By the way, if you find a mistake, select the misspelled word and press Ctrl + Enter on your keyboard. Thanks in advance!
5. Install the heating element
Perhaps the most interesting and concise part. Installation is in the reverse order. Insert the heating element all the way, you can tap it a little. Throw a nut on the stud, hold out. Fasten the grounding, screw on the second nut. Pull the terminals onto the contacts of the heating element. Close the back cover.
Everything, you can call the testers of the washing machine and check.
Perhaps this was the end of the description. However, I want to note that it would not hurt to regularly clean the built-in filter. When cleaning the filter, it is a good idea to disconnect the rubber hose from the drum drain and rinse it thoroughly. Scale stones accumulate there.
This concludes the long story about a quick and easy self-repair of the washing machine. I wish you a pleasant and trouble-free operation of your reliable assistant in the fight against clothing pollution!
In the end, I found a video with a good demonstration of the process of replacing the heating element on the washing machine. There is a heating element with a temperature sensor.
Is the laundry poorly cleaned? Perhaps the reason is the lack of heating? To be sure of a breakdown, you need to know how to remove the heating element from the washing machine (CM). After that, you can diagnose and replace the element. We will show you how to do it yourself at home.
Reasons for dismantling and location of the heating element in the washing machine
The machines are connected to cold water, after which it is brought to the desired temperature using a heating element. If the tubular element is defective, then the water does not heat up, the powder dissolves poorly, and stains on clothes remain in place. The main reasons for the breakdown of the heating element:
- Scale.
- Short circuit, voltage drops in the network.
- Wear after long-term use.
An indirect sign of the lack of heating is a cold hatch 20-25 minutes after the start of washing.
The location of the heater depends on the brand and model of the CMA. Look at the instructions, perhaps the manufacturer indicated the location of the heating element.
If there is no such information, then inspect the body of the washing machine. A large back cover indicates that the heater is located behind it. If the panel does not occupy the entire back wall, it is likely that only the belt is accessible.
As a rule, in models “ Ariston ", Ardo," Kandy "," Indesit ", Electrolux," Zanussi "," Atlant " The heating element is located at the back of the washing machine.
In CM LG, " Samsung "," Bosch ", Siemens, Whirpool the element is located on the front side.
In Hansa washing machines, access is opened through the basement panel. And in the technique with vertical loading - through the end one.
How to remove the heating element?
Having decided on the location, you can proceed to disassembly.
Observe safety precautions before starting work. Disconnect the washing machine from the network and communications.
Prepare a container before disconnecting the hoses from the panel; water may flow from them. You also need to drain the remaining liquid from the machine.
- Open the filter door under the loading door.
- Substitute a container and unscrew the drain filter counterclockwise.
- Unclog it if necessary.
Proceed to dismantle the back cover:
- Remove the top cover bolts at the back.
- Slide it back and remove it from the case.
- Remove the screws around the perimeter of the rear panel.
- Under the loading tank you will see the heating element terminals.
How to remove the front wall:
- After removing the top cover, remove the powder dispenser. To do this, press the latch in the center and pull it towards you.
- Remove the control panel bolts.
- Disconnect the wires from the electronic board, or simply leave the panel on top of the CMA.
- Open the hatch door.
- Remove the clamp from the sealing rubber.
- Remove the two screws securing the door lock.
- Place your hand between the panel and the door. Take out the lock, disconnect the contacts.
- Unscrew the bolts of the front wall and remove it from its place.
The plinth panel is located below, under the loading hatch. It is fastened with latches or bolts.
As soon as access to the element is opened, it must be obtained. How to properly pull the heating element out of the case:
- Take a picture of the wiring connection.
- Disconnect the wiring from the element pins.
- Using a socket wrench, unscrew the center nut (not completely).
- Push the bolt inward, after which the part can be removed from the socket.
- Sometimes the seal interferes with easy removal. Therefore, pry the element with a screwdriver.
In the case of some heaters, a thermal sensor is installed. The device measures the water heating temperature by sending signals to the control module. As soon as the values reach those indicated on the thermostat, the board turns off the heating element.
Pull the sensor out of the housing. Replacing it is easy by installing a new part in place. After removing the heater, inspect it for scale, diagnose short circuit, open circuit. If faulty, install a new element. Read more in the article “ How to connect a heating element of a washing machine».
The installation of purification filters for water, as well as the use of voltage stabilizers, will help to avoid quick breakdown of the tubular element. Take care of long-term operation in advance.
